Preview only. Not live.
Inovus Building SolutionsACMV, air quality & electrical Book a site survey

Demo plant running live below

Cooling, clean air and power for buildings that never stop.

ACMV and electrical systems for malls, hospitals, semiconductor plants and factories. Modelled in Revit, load-tested for 36 hours, then run at peak efficiency by our energy control system.

Book a site survey Check your plant in 60 seconds
3D model of a chiller plant room with chillers, pumps, colour-coded pipework, an AHU and ductwork
Drag to rotate. Tap a number.
Plant room model

Chillers

Plant efficiency0.61 kW/TR
Cooling load- TR
Plant power- kW
Saved today-
Demo control systemOpen it
  • 36 h load test before handover
  • 98% reliability in year one
  • 72 h repair during defect liability
  • 24/7 emergency response

What we build and look after

Design-build or install-only, new build or retrofit. One project team from the first survey to after-sales support.

Air handling units with insulated ductwork and pipework in a commercial plant room
Mechanical (ACMV)

Air handling, ventilation and ductwork

Our core work since day one. We size, route and install the systems that move conditioned air through the building.

Air handling unitsSelection, installation and coil connections
Fan coil unitsFor rooms, offices and tenant spaces
DuctingDesigned in 3D, fabricated and installed
Mechanical ventilationFresh air, exhaust and smoke control
VRV and DX-splitFor tenants and smaller buildings
Building automationHVAC controls that run to schedule
Insulated pipework manifold with valves, actuators and gauges
Chilled water and piping

Chiller plants, pumps and pipework

The heart of a central cooling system. We size it to the building's load and build it to run efficiently for decades.

ChillersAir- and water-cooled, sized to the load
PumpsSelected with flow and pressure simulation
Chilled and condenser waterPiping, valves and insulation
Heat exchangersFor process and plant loads
Industrial and process pipingFor factories and fabs
PlumbingSupply and drainage
Air handling unit with clean, insulated duct connections
Indoor air quality

Cleaner air, cleaner coils

Better air for the people inside, and coils that stay clean so the system uses less power.

UV-C lampsContinuous protection on the coils
Bipolar ionisationHelps break down airborne pathogens
Filter upgradesThe fastest improvement for most buildings
Duct cleaningRemoves dust, mould and debris
Electrician carrying out maintenance inside an electrical panelTechnicians servicing the wiring of an air-conditioning unit
Electrical and maintenance

Power to run it, technicians to keep it running

Design-build electrical works for the systems we install, and maintenance plans that keep them at design performance.

High and low voltageIndustrial and commercial
Medium-voltage switchgearFabrication and installation
UPS and generatorsBackup power for critical rooms
ELV and solarExtra-low voltage systems and solar
Preventive maintenanceChillers, AHUs, FCUs and pumps
24/7 emergency responseOn maintenance plans

Energy Efficiency Control System

Our chiller plant control system runs your central plant at its most efficient point, minute by minute. It stages chillers, resets setpoints and trims pumps and tower fans to the real load, and shows every kilowatt it saves.

  • MonitorLive status of every chiller, tower and pump
  • ControlAutomatic sequencing and setpoint reset
  • OptimiseLower kW/TR, lower power bills
  • ProtectAlarms and early fault detection, plus RA 11285 energy reports
Chiller Plant Monitoring & ControlDemo with simulated data
--:--:-- Operator
Plant efficiency
-kW/TR
Cooling load
-TR
of 1,500 TR installed
Plant power
-kW
chillers, pumps, towers
CHW supply / return
-°C
-
Saved today
-kWh
-
Hot condenser water to towersCondenser water from towersChilled water supplyChilled water return

Demo only: the numbers are simulated for a typical 1,500 TR plant and are not from a real site. Real savings depend on the plant, so we measure your baseline before we quote a figure. Benchmarks: well-run plants reach 0.65 kW/TR or lower; many plants run at 0.9 to 1.2 kW/TR.

Is your chiller plant in trouble?

Answer six quick questions. You get a health score, the biggest risks in your plant, and what to do about each one.

1How old are your chillers?
2Which refrigerant do they use?
3Your power bill over the last two years
4Complaints about heat or humidity
5How is the plant controlled?
6How is it maintained?

What would your plant save?

Enter four numbers about your chiller plant. You get an estimate of the yearly saving from our energy control system, and the budget it would pay back within three years.

Type of building
Scope
Estimated saving per year ₱0
Today
-
With IBSI
-
Energy saved
-
CO₂ avoided
-
Plant efficiency after
-
Saving over 10 years
-
A project costing up to₱0would pay for itself within 3 years.
Get a free energy audit

Estimate only. Assumes an average 60% plant load and typical operating hours for the building type. Published optimisation projects save 15 to 30% with controls alone and 40 to 55% with plant upgrades. We measure your real baseline during the audit.

Modelled in Revit first, so it fits on site the first time

We model every plant room, pipe route and duct run in Revit before anything is cut. Clashes get fixed on screen, not on the ceiling, and you see exactly what you are paying for.

Photo of the finished chiller plant room 3D model of the same chiller plant room, from the same viewpoint Revit 3D modelSite photo

Drag across: the coordinated 3D model on the left becomes the finished room on the right. Same viewpoint, same pipes, same equipment.

Clash-free routesPipes, ducts and cable trays coordinated before installation
Sized by calculationLoads, pipe sizes and pump flow checked against ASHRAE
Finished to a high standardAluminium-jacketed pipework and foil-faced duct insulation with taped seams
As-built at handoverThe model and drawings match what is installed

Three kinds of building, three different jobs

A mall, a hospital and a chip plant need different things from their air. We design for each one.

Multi-level mall atrium

Malls and commercial buildings

Comfortable shoppers and tenants from opening to closing, without a power bill that keeps climbing.

  • Central chilled-water plants
  • AHUs, FCUs and ventilation
  • VRV for tenant spaces
Air handling plant room

Hospitals and healthcare

Clean air for patients and staff, and cooling that doesn't stop mid-procedure.

  • IAQ upgrades, UV-C and ionisation
  • Filter upgrades and duct cleaning
  • UPS and generator backup
Plant corridor lined with insulated pipework

Semiconductor plants and factories

Stable temperature and airflow for production, and the piping and power behind it.

  • Process cooling and piping
  • Heat exchangers
  • Medium-voltage switchgear

What you get when we hand over

Handover isn't the end of the job. We back every cooling system for a full year after it.

Before handover

36-hour load test

The whole system runs under load for 36 hours, tested against AHRI, ASHRAE or ISO standards.

At handover

Full documentation

As-built drawings, system layouts and schematics, and a plain summary of what was installed.

First 12 months

Defect liability period

98%system reliability, with no more than 3 hours of downtime

72 hto repair a failed unit, while the backup keeps running

How we deliver a project

Seven steps, one project team, from the first visit to after-sales support.

  1. ConsultationYour needs, budget and constraints
  2. Site surveyYour drawings checked against the real site
  3. 3D designLoads, pipes and ducts sized to ASHRAE and local codes
  4. InstallationOne project manager working with you and the main contractor
  5. Testing & commissioningFull tests, then 36 hours under load
  6. HandoverAs-built drawings and system documents
  7. Support1-year defect liability, then maintenance
OSHA 10-hourCertified site crews
OSHA 30-hourCertified managers
Think 5x5Safety check before every task
ASHRAE / AHRI / ISODesign and test standards

Clients we have worked with: malls and banks, hospitals, manufacturers and public institutions

SM Supermalls and SM Prime BDO Unibank China Bank St. Luke's Medical Center Siemens Healthineers GE Healthcare Microchip Ampleon Daikin Tosot Landmark National Museum of the Philippines

Questions facility teams ask us

Anything else, call us and we'll arrange a visit.

Do you take on new builds or only retrofits?

Both. We design and build new systems, upgrade existing ones and maintain what's already running.

Will we see the design before you build?

Yes. We model the plant room, pipework and ductwork in 3D and walk you through it before installation starts.

Can you work alongside our main contractor?

Yes. Our project manager coordinates with you, your suppliers and the main contractor throughout.

What happens if something fails after handover?

For cooling systems, the first year is covered by our defect liability period. A failed unit is repaired within 72 hours while the backup runs.

Do you offer maintenance contracts?

Yes. Preventive maintenance and IAQ programmes with 24/7 emergency response, renewable after the first year.

Book a site survey

Tell us about your building. We'll arrange a visit and come back with options that fit your budget.

Inovus Building Solutions Inc.Unit B, 121 East Main Avenue, Laguna Technopark, Special Economic Zone, Biñan, Laguna 4024

We use your details only to reply to this request.